Big Joe CB22 Specificactions Sheet
Welcome to interactive presentation, created with Publuu. Enjoy the reading!
2200 lbs. at 24” load center
Compartment: 26.37” x 9.01” x open. An-
derson 175 Gray—A-11 Minimum battery
weight 340 lbs.
24-volt ZAPI ACO Travel Controller
Variable from 0 mph to 3.4 mph empty
Variable from 0 mph to 3.1 mph loaded
4º Back 2º Forward
Up to 33 fpm empty.
Up to 25 fpm loaded
Up to 29 fpm empty.
Up to 57 fpm loaded
TIRES / WHEELS
9” x 3” polyurethane
��” x �” polyurethane
Lift cylinder is hard chrome. Pump unit
includes motor, gear pump, and solenoid.
Pressure compensated lowering valves
regulates lowering speeds.
ZAPI AC travel controller and AC drive
motor provides high torque throughout the
entire drive range. Regenerative braking
and brushless design drastically reduces
Travel speed remains constant relative to
throttle position regardless of the load on
truck. Automatic resetting circuit breaker
and one piece micro switch design com-
plete the system.
Electromagnetic brake is mounted on mo-
tor armature shaft multiplying the braking
power through the ZF GK10 transmission.
Brake is applied when control arm is in the
vertical or horizontal handle position.
Travel speed is reduced when forks are
above 12” fork height. Neutral braking re-
sists roll back on ramps.
Travel, lift, lower and tilt functions are
located in the ergonomic operator handle,
designed to allow operation with either
hand. Wrap around guard, reversing
switch, thumb control, and horn are stand-
Vertically mounted drive motor is direct
mounted to gear housing. Oil bathed ZF
GK10 hypoid bevel gear drive-train
transfers power to axle. State of the art
optimized gear technology supplies
advantages such as minimal envelope
circle, zero maintenance, low noise level,
high efficiency and high performance.
FRAME AND MAST
Bolt-on high visibility I-beam construction,
lift cylinders are positioned in outer I-beam
for good operator visibility through mast.
Dual lifting chains.
Class two ITA fork carriage with 36” tall
load back rest.
sealed in oil bath
LOAD WHEELS-Sealed ball bearings
Removal of two piece power head cover
exposes major components for inspection
and maintenance. Drive wheel is removed
with one nut.
Regenerative Neutral Braking
Gas Assist Spring Handle
Hour Meter BDI Combo Gauge
35” Tall Load Backrest
Four Pack Power MF 224 AH / 5.4
kwh 110VAC plug-in charger
Industrial Battery 255 AH 5.9 kwh
2200 Lbs. Capacity
Power Drive Counterbalance Stackers
Big Lift LLC
All units are built to be in compliance with the Occupational Safety & Health Act (OSHA)
Big Lift LLC will not assume liability for injuries or damage arising from, or caused by, the removal of any safety devices from their vehicles by user. Because of
the Big Lift LLC continuing product improvements, specifications are subject to change without notice.
© Copyright 201�, Big Lift LLC Printed USA 0815
2200 Capacity @ 24" Load Center ITA Class II Fork Carriage
Aisle dimensions listed above assume 4” be-
tween loads. Use the larger dimension; load
width or load length. For ease of use and add 6”
to 12” for operator clearance to the appropriate
specifications listed above. Truck performance
may vary due to application requirements' and
changes in model design.
Add: 2” to aisle for model CB22-157 with
triple stage mast.
CB22 - Right Angle Stacking
For ease of use add 6 to 12” to aisle dimension listed
³ Estimated shipping weight without battery
*Derate 400 lbs. above 128” w/ 224AH battery pack.
*Consult factory for derate with industrial battery.